Skip to main content
SEA URCHIN in 2007
Sea Urchin
SEA URCHIN in 2007
SEA URCHIN in 2007
Private Collection

Sea Urchin

Vessel numberHV000266
Vessel Registration NumberIJ882Q
Previous owner (Australian, founded 1913)
Date1953
DimensionsVessel Dimensions: 9.14 m x 2.48 m x 0.88 m, 5.41 tonnes (30 ft x 8.15 ft x 2.9 ft, 5.5 tons)
DescriptionSEA URCHIN was built as a showpiece at the Queensland State Dockyard. The 9.14 m (30 ft) long Huon pine planked craft was completed by four apprentices under the direction of foreman shipwright John Wassin.

It was built as an open boat to be used when the Royal couple visited the Great Barrier Reef aboard the Royal Yacht GOTHIC. The bottom of the launch was fitted with two 450mm (18 in) diameter brass rimmed double-glazed viewing portholes. Inside the cockpit viewing scopes were placed over the portholes for looking at the coral as the launch passed over the reef. SEA URCHIN was put aboard GOTHIC for the reef visit, but because of bad weather on the day, it was never used for its intended purpose.

The launch remained in Queensland after the GOTHIC left Australian waters.

In 1955 Queensland Harbours and Marine converted SEA URCHIN for use as an advanced survey vessel to undertake cross section echo-sounding of the Brisbane River. A cabin was added and it was fitted with the latest Kelvin Hughes MS26 dry-paper hydrographic echo-sounder. Previously, soundings had been taken by lead-line from small rowing boats or outboard powered craft.

The echo-sounding was a very precise method which required SEA URCHIN to be manoeuvrable and maintain a constant speed as it crossed from bank to bank, with the added ability to stop within two boat lengths. These requirements were met by fitting a Kitchener rudder, especially imported from England. A curious device in the form of a scoop made in two halves, the rudder directs water flow off the propeller to steer, stop and reverse the craft. It was very effective and needed to be used with care. A change in direction was sudden and crew members could fall overboard if caught unawares.

When the survey work was completed around 1960, SEA URCHIN became the paymaster's vessel, with the task was of paying labourers along the river working for the Brisbane Port Authority. In 1967 it was fitted with a new Cummins diesel engine.

It is understood that when the harbourmaster retired around 1970 he was able to buy the launch which he converted into his own private vessel at Southport, Queensland. In the 1990s it was sold and taken north to Noosa on the Sunshine Coast where in 1998 shipwright Vic Devonshire carried out an extensive restoration.

The craft changed ownership again and moved south to Port Stephens in New South Wales. In 2008 the brass rims for the portholes in the hull remained in place but the glazing had been covered over and the Kitchener rudder replaced by a conventional blade. The strongly built hull retained virtually all of its original planking and structure, and the superstructure represents the configuration of the 1970s.








SignificanceSEA URCHIN is a timber launch built in Queensland in the early 1950s It was built by the Queensland State Dockyard in 1953 for Queen Elizabeth II's first visit to Australia the following year. It was then taken over by Queensland Harbours and Marine and used as a survey and paymaster's vessel, it had a long association with the port of Brisbane.
PARRY ENDEAVOUR on display in 2013
R Williams & J Chute Partnership
1979
Derwent Hunter in the Whitsundays
Walter Wilson
1946
SEAWAVE after restoration in 2007
Lars Halvorsen Sons Pty Ltd
1950
On Lake Alexandrina in 1887-89
Willans and Robinson
1884
KRAIT restored for the 75th Anniversary event on 26th September 2018 at the ANMM wharves.
c 1934
WANGADIR at Scarborough Qld 2012
Watts & Wright
1940
GRETEL in Italy in 2003
Lars Halvorsen Sons Pty Ltd
1962
PADDY MCCANN in 2007.
Williamstown Dockyard
1888
PV RICHMOND crossing the bar at Ballina
W Holmes Boat Builder
1932
ATHENE, possibly  in the early 1930s
WM Ford Boatbuilders
1905